Poducts

  • Bitumen Tests- Tests of Bitumen- Bitumen Lab Tests

    Bitumen Tests with IS Codes. Summary. Requirements of bitumen as a binding material and its different forms were discussed. Various tests are conducted on bitumen to assess its consistency, gradation, viscosity, temperature susceptibility, and safety. Standard test procedures on bitumen were also covered in this chapter. Problems

  • 9 TEST TO CHECK QUALITY OF BITUMEN FOR USE IN

    11.09.2015· A steel ball is placed upon the bitumen sample and the liquid medium is heated at a rate of 5 0 C per minute. Temperature is noted when the softened bitumen touches the metal plate which is at a specified distance below. Generally, higher softening point indicates lower temperature susceptibility and is preferred in hot climates. Fig-3 shows Softening Point test setup. Also Read: Softening

  • Laboratory Tests of Bitumen to Check Quality | Tests on

    Laboratory Tests of Bitumen to Check Quality. Various Tests are conducted on Bitumen to assess its Consistency, Gradation, Viscosity, Temperature Susceptibility and Safety. There are a number of Tests to assess the properties of Bituminous materials. The following Tests usually conducted to evaluate different properties of Bituminous materials.

  • Laboratory Testing Statens vegvesen

    Laboratory Testing 2000 3.1 Pre-conditioning of Bitumen Samples Prior to Mixing or Testing NPRA 014 test 14.511 3.2 Density of Bituminous Binders ASTM D70-97 3.3 Flash and Fire Point by Cleveland Open Cup ASTM D92-90 3.4 Thin-Film Oven Test (TFOT) ASTM D1754-87 3.5 Penetration of Bituminous Materials ASTM D5-86 3.6 Softening Point Test ASTM D36-70 3.7 Ductility ASTM D113

  • List of Tests for Bitumen as per Indian Standard » Civil

    04.08.2019· For details procedure and calculation, check out my article on Softening Point Test Of Bitumen As Per IS: 1205-1978. Specific Gravity Test; In paving jobs, to classify a binder, density property is of great use. In most cases, bitumen is weighted. But when used with aggregates, the bitumen is converted to volume using density values. The density of bitumen is greatly influenced by

  • 5/5(20)
  • FIELD SAMPLING AND TESTING MANUAL SECTION 400

    Bitumen: Tests and frequency for IA for viscosity and sieve are shown in Table 401-5. Table 401-5 Test Frequency AASHTO T 59, “Emulsified Asphalts” 2 test results per project. Tolerance between IA and acceptance tests are in Table 4 01-6. Table 401-6 Test Tolerance AASHTO

  • IIT Kanpur

    IIT Kanpur

  • CHAPTER 10 TESTS FOR BITUMEN & BITUMINOUS MATERIALS

    Chapter 10 Standard Test Procedures Tests For Bitumen & Bituminous Materials MAY 2001 Page 10.3 d) To maintain the sample at the correct temperature during the test, a glass transfer dish is used. This dish of at least 350 ml capacity is fitted with a suitable support to hold the sample container firm and level during testing.

  • 文件大小: 189KB
  • MATERIALS TESTING MANUAL Department of Infrastructure

    The Department of Infrastructure Test Methods and Codes of Practice contained in this Materials Testing manual shall take precedence over all test methods and procedures, and shall be used in conjunction with relevant Australian Standards. Where tests are required which are not included in the manual, the appropriate Australian Standard method shall be used. In special circumstances where

  • 7 LAB TESTS ON AGGREGATE TO CHECK QUALITY FOR USE

    12.09.2015· Several laboratory tests are conducted to arbitrarily determine the adhesion of bitumen binder to an aggregate in the presence of water. Static immersion test is one specified by IRC and is quite simple. The principle of the test is by immersing aggregate fully coated with binder in water maintained at 40 0 C temperature for 24 hours.

  • Pavement materials: Bitumen

    A brass ring containing test sample of bitumen is suspended in liquid like water or glycerin at a given temperature. A steel ball is placed upon the bitumen sample and the liquid medium is heated at a rate of 5 C per minute. Temperature is noted when the softened bitumen touches the metal plate which is at a specified distance below. Generally, higher softening point indicates lower

  • HHPPP BBIITTTUUUMMMEEEN NN

    6 Tests for VG Grade Bitumen 9 13 7 Aging of Bitumen 14 15 8 Field Abnormality 16 18 9 Modified Bitumen 19 20 1 List of Frequently Used Codes, Specifications & Standards 40 – 41 2 Commonly used Conversion Factors 42 – 43 3 Customer Sales Offices 44 – 46 . 1 1. iNTRODUCTION Bitumen is manufactured from crude oil. Bitumen is obtained as the last residue in fractional

  • (PDF) Highway Material Testing Manual ResearchGate

    S.K. Khanna and C.E.G. Justo (1971), Highway Material Testing: Laboratory Manual. References IS: 2386 (Part 1)-1963 Methods of Test for Aggregates for Concrete-Part 1 Particle size and Shape.

  • Building Materials Laboratory Manual

    Building Materials Laboratory Manual Fall 2007 -2008 Prepared by: B. J. Farid 4 How to write a laboratory report The following arrangement of t he report is suggested: Title This should indicate the nature of the test and the specifications number used.

  • IS 13311-1 (1992): Method of Non-destructive testing of

    test as per IS 456 : 1978 Code of practice for plain and reinforced concrete ( thirdrevision )’ or IS 1343 : 1980 Code The intrinsic difference between the laboratory test specimens and in-situ con- crete, for example, surface texture, moisture condition, presence of reinforcement, etc, also affect the accuracy of results. The correlation is valid only within the range of values of pulse

  • Bitumen Testing: Solvent Extraction vs Ignition Furnace

    The manual test method uses the Gilson HM-378 Asphalt Content Furnace and requires manual weighing and recording of the specimen before and after the ignition procedure. Automated systems such as the Thermolyne® NCAT Furnace automatically weigh, record and report completed test results. Still, have questions about asphalt content testing

  • IS Codes List Indian Standards in Civil Engineering

    Code No. Description; IS 4031: Method of physical tests for hydraulic Cement: IS 650: Specification for Standard sand for testing of Cement : IS 383: Specification for Coarse and Fine aggregate for use in mass concrete: IS 515: Specification for natural and manufactured aggregate for use in mass concrete. IS 2387: Method of test for aggregates for concrete. IS 516: Methods of test

  • Final List Of Labs IIT Kanpur

    S.No. Name of the Laboratory Contact Details Certificate No. Product / Material of test Test Type Specific Test Performed Date of Issue Date of Expiry Construction Water Cement Fly Ash Gypsum & Its Products Aggregates Bitumen Cement Concrete Fly Ash Tiles Clays & Soils Ultimate Tensile stress % Elongation Yield Strength Bend Test Rebend Test Mass / Meter Consistency Setting Time Initial

  • LABORATORY DETERMINATION OF CALIFORNIA BEARING RATIO

    LABORATORY DETERMINATION OF CALIFORNIA BEARING RATIO STANDARD IS: 2720 (Part 16) 1979. DEFINITION California bearing ratio is the ratio of force per unit area required to penetrate in to a soil mass with a circular plunger of 50mm diameter at the rate of 1.25mm / min. APPARTUS Moulds 2250cc capacity with base plate, stay rod and wing nut confirming to 4.1, 4.3 and 4.4 of IS: 9669

  • ASTM D2172 / D2172M 17e1 Standard Test Methods for

    C128 Test Method for Relative Density (Specific Gravity) ICS Code. ICS Number Code 91.100.50 (Binders. Sealing materials); 93.080.20 (Road construction materials) UNSPSC Code. UNSPSC Code 15121902(Grease) UNSPSC Code. UNSPSC Code 30121500(Bituminous derivatives) Referencing This Standard. Link Here : Link to Active (This link will always route to the current Active version of the

  • LAB MANUAL vvitengineering

    lab manual. ce6612 – concrete 2013 ce6612-concrete and highway engineering laboratory list of experiments test on fresh concrete 1. slump cone test 2. flow table 3. compaction factor 4. vee bee test test on hardened concrete 1. compressive strength – cube & cylinder 2. flexture test 3. modulus of elastics test on bitumen 1. penetration 2. softening point 3. ductility 4. viscosity 5

  • (PDF) Highway Material Testing Manual ResearchGate

    S.K. Khanna and C.E.G. Justo (1971), Highway Material Testing: Laboratory Manual. References IS: 2386 (Part 1)-1963 Methods of Test for Aggregates for Concrete-Part 1 Particle size and Shape.

  • Bitumen Testing: Solvent Extraction vs Ignition Furnace

    The manual test method uses the Gilson HM-378 Asphalt Content Furnace and requires manual weighing and recording of the specimen before and after the ignition procedure. Automated systems such as the Thermolyne® NCAT Furnace automatically weigh, record and report completed test results. Still, have questions about asphalt content testing

  • Building Materials Laboratory Manual

    Building Materials Laboratory Manual Fall 2007 -2008 Prepared by: B. J. Farid 4 How to write a laboratory report The following arrangement of t he report is suggested: Title This should indicate the nature of the test and the specifications number used.

  • Bitumen Testing Equipment Ductility Testing Machine

    Loss on Heating test is conducted for determining the loss in weight of bitumen and flux-oils on heating as per the requirements of IS: 1212. Instructions:- The Oven is having a double walled Internal Chamber of 400mm x 400mm x 400mm (16” x 16” x 16”) made of Stainless Steel and External Body made of Mild Steel Sheet (Powder Coated Paint) or Stainless Steel Sheet with glass wool

  • Three-Year Field Test Summary for Experimental Modified

    Construction Research Laboratory Engineering S ELECTE _•FEB 2 3 19931 C Three-Year Field Test Summary for Experimental Modified Bitumen Roofing at Fort Polk, LA by David M. Bailey Wafter J. Rossiter James F. Seiler, Jr. This report presents results of the first 3 years of a 10-year field evaluation on three modified bitu-men roofing systems at Fort Polk, LA. This work is part of a research

  • CIVIL INDIAN STANDARD (IS) CODES: IRC 37 2012

    tags:civil engineering code book,is code, Indian standard code books, anna university code books, IS3370, IS456, SP16, IRC37 2001,IRC 37 2012,IRC 37 2012 GUIDELINES FOR THE DESIGN OF FLEXIBLE PAVEMENTS . CIVIL INDIAN STANDARD (IS) CODES indian standard code of practice,IS 3370 PART 1 2 3 4,IS 456,SP 16,IRC 37 2001,IRC 37 2012,IS 1343,CE 2038,CE 2255,design of

  • ASTM D2172 / D2172M 17e1 Standard Test Methods

    C128 Test Method for Relative Density (Specific Gravity) ICS Code. ICS Number Code 91.100.50 (Binders. Sealing materials); 93.080.20 (Road construction materials) UNSPSC Code. UNSPSC Code 15121902(Grease) UNSPSC Code. UNSPSC Code 30121500(Bituminous derivatives) Referencing This Standard. Link Here : Link to Active (This link will always route to the current Active version of the

  • Final List Of Labs IIT Kanpur

    S.No. Name of the Laboratory Contact Details Certificate No. Product / Material of test Test Type Specific Test Performed Date of Issue Date of Expiry Construction Water Cement Fly Ash Gypsum & Its Products Aggregates Bitumen Cement Concrete Fly Ash Tiles Clays & Soils Ultimate Tensile stress % Elongation Yield Strength Bend Test Rebend Test Mass / Meter Consistency Setting Time Initial

  • LABORATORY DETERMINATION OF CALIFORNIA BEARING

    LABORATORY DETERMINATION OF CALIFORNIA BEARING RATIO STANDARD IS: 2720 (Part 16) 1979. DEFINITION California bearing ratio is the ratio of force per unit area required to penetrate in to a soil mass with a circular plunger of 50mm diameter at the rate of 1.25mm / min. APPARTUS Moulds 2250cc capacity with base plate, stay rod and wing nut confirming to 4.1, 4.3 and 4.4 of IS: 9669